SIDOOR ATE500E elevator door drive Siemens

Область применения

The SIDOOR ATE500E comfort elevator door drive is an intelligent door control system which enables the opening and closing of cabin and shaft doors at adjustable speeds and accelerations.

The maintenance-free drive unit is speed controlled and comprises an electronically commutated SIDOOR MED280 EC direct drive designed for a maximum of 280 kg total door panel weight.

Must be ordered separately, see "Direct drives".

Operation of the elevator door drive does not require limit switches. The door width and the "OPEN"/"CLOSE" positions are determined automatically.

The current operating states are indicated by a 7-segment display directly in the SIDOOR ATE500E elevator door drive. They can also be displayed externally using the Software Kit or Service Tool, see "Additional units".

Forces are transferred via a toothed belt which passes over a deflector unit and can be fitted with two door clutch holders. These accessories are not included in the scope of supply, see "Accessories".

Both single-leaf and centrally opening doors can be driven.

Обзор

SIDOOR ATE500E elevator door drive

The SIDOOR ATE500E elevator door drive enables the quick, easy and versatile installation, configuration and operation of EC technology gearless elevator door systems.

• Design:
  • Relay module
  • CAN module
• For dynamic door weights up to 280 kg
• High control performance und optimized drive characteristic transitions
• Automatic door weight detection (single-button commissioning)
• 6 kg maximum counterweight of the coupled floor door
• Operating temperature -25 to +50 °C without restrictions
• Automatic identification of the connected motor
• Opening width 0.3 to 5 m
• Auxiliary voltage output 24 V DC ± 15 %; 0.4 A (short-circuit-proof)
• Output stage short-circuit-proof
• Optimized energy consumption during cabin operation (DCPS)
• Vandal-proof
• IP20 degree of protection
• The current operating states are indicated via a 7-segment display directly in the elevator door drive or externally using the Software Kit or Service Tool, seeAdditional units.

Дизайн

The SIDOOR ATE500E Elevator Door Drive system comprises a number of components:

Конфигурация

During initial commissioning, please note the following:

• Mechanical mounting and setting, see the SIDOOR EC System Manual, and the ATE500E and MED280 Operating Instructions
• Electrical configuration and commissioning:
  • Push the door into the "CLOSED" position.
  • Open the device cover
  • Plug in the motor connector
  • Connect NT40 switch mode power or SIDOOR Transformer to 230 V AC mains supply
  • Press and hold the learn run button
  • Connect NT40 switch-mode power supply or SIDOOR Transformer to the input of the SIDOOR ATE500E elevator door drive
  • The learn run starts automatically and the learn run button can be released as soon as the door starts to move
  • On completion of the learn run, the door is in the "CLOSED" position and the 7-segment display indicates "u".
  • The door can now be moved using the "OPEN" and "CLOSE" buttons with the default profile.

Особенности

• 1-button operation for the entire commissioning process.
• Excellent performance (velocity up to 800 mm/s and acceleration up to 3000 mm/s²) permit fast door opening.
• SIDOOR FOC stands for excellent control quality and a weight-independent, travel curve optimized control response.
• Low noise during operation
• Service life with gearless EC direct drive is longer since there are only a small number of components susceptible to wear installed.
• Reduced service requirements and fault minimization during parameter assignment.
• Asset minimization through the use of standardized SIDOOR additional units and power supplies.
• Only one motor required for different drive directions left/right
• SIDOOR User Software (part of the SIDOOR Software Kit, not included in the scope of supply, see "Additional units") enables user-friendly operation and detailed diagnostics.
• The SIDOOR Service Tool enables simple setup and diagnostics via an event and statistics memory.
• Easy selection of different drive profiles using the "Minimal editor" function.
• Small footprint thanks to compact design.
• Automated functions for enhanced safety.

Програмирование

The Software Kit is available as a separate unit(see "Additional units"); it facilitates user-friendly parameter settings and oscilloscope functions via the SIDOOR User Software (part of the SIDOOR Software Kit).

Технические данные

Дальнейшая информация

For further product details, refer to the

• "SIDOOR EC Systems" System Manual, http://support.automation.siemens.com/WW/view/en/101978636