Range of training courses Siemens

Обзор

SINAMICS DCM Service and commissioning

Description/learning objective

This training course explains how you adapt the parameter settings of the converter to the application and the DC motor. You expand your theoretical knowledge in the form of exercises carried out on special training equipment. After participating in the course, you know the functions of a converter and the interfaces. You are in a position to safely and quickly commission the unit. Through routine fault diagnostics and troubleshooting, you save time and optimize the availability of your plant or system.

Target group

Commissioning engineers, project engineers, service personnel

Preconditions

Basic knowledge of electrical engineering

Content

• Design and function of the SINAMICS DC MASTER converter: Control module CUD, power section, field circuit, interfaces
• Commissioning and parameterizing using the BOP20 and AOP30 operator panels and the STARTER PC program
• Using the memory card: Structure and data backup
• Procedure when commissioning, checking functions
• Optimizing the closed-loop current and speed control, automatic optimization
• Function diagrams: Setpoint channel, inputs and outputs, free function blocks
• Information on Drive Control Chart DCC
• Drive interface to PROFIBUS / PROFINET
• Expanding the system using Terminal Modules and Sensor Modules via DRIVE-CLiQ
• Parallel connection and peer-to-peer coupling
• Operating states, alarms and fault messages
• Service functions: Trace, measuring functions, diagnostics memory
• Practical exercises using AOP30 and STARTER on training equipment

SINAMICS DCM Upgrade for SIMOREG experts

Description/learning objective

You already have good know-how on the previous SIMOREG DC-MASTER unit. This training course explains how you adapt the parameter settings of the SINAMICS DC MASTER to the application and the motor. You expand your theoretical knowledge in the form of exercises carried out on special training equipment. After participating in the course, you know the functions of a converter and the interfaces. You are in a position to safely and quickly commission the unit. Through routine fault diagnostics and troubleshooting, you save time and optimize the availability of your plant or system.

Target group

Commissioning engineers, project engineers, service personnel

Preconditions

Good knowledge about SIMOREG 6RA70

Content

• Design of the SINAMICS DC MASTER converter: Control module CUD, power section, field circuit, interfaces
• Commissioning and parameterizing using the BOP20 and AOP30 operator panels and the STARTER PC program
• Using the memory card: Structure and data backup
• Function diagrams: Setpoint channel, inputs and outputs, free function blocks
• Information on Drive Control Chart DCC
• Drive interface to PROFIBUS / PROFINET
• Expanding the system using Terminal Modules and Sensor Modules via DRIVE-CLiQ
• Parallel connection and peer-to-peer coupling
• Operating states, alarms and fault messages
• Service functions: Trace, measuring functions, diagnostics memory
• Practical exercises using AOP30 and STARTER on training equipment

SINAMICS DCM Servicing

Description/learning objective

Unplanned stoppages of production machines can cost a lot of money.

In this course you will learn the proper way to handle the SINAMICS DC MASTER DC converter. You will be able to adapt the parameter assignment and carry out data backups for modifications to the system. In the event of failures you will be in a better position to analyze the faults and to clear them more quickly. That will save time and money.

Target group

Service personnel, maintenance personnel

Preconditions

Basic knowledge of electrical engineering

Content

• Structure and function of the SINAMICS DC MASTER converter
• Changing parameters, backing up data and performing diagnostics with:
  • BOP20 and AOP30 operator panels
  • STARTER PC program
• Using the memory card
• Establishing the signal flow using function charts:
  • Setpoint channel
  • Inputs and outputs
  • Interfaces to fieldbuses
• Checking the operating state and enable signals
• Test mode with STARTER:
  • Operation with the control panel
  • Recording of signals using the trace function
  • Triggering for faults and bit patterns
• Use of the trend recorder function for long-term recording
• Analysis of alarms and fault messages
• Read-out of the diagnostic memory
• Thyristor diagnostics service function
• Replacement of Control Unit, fan and fuses
• Information on servicing DC motors
• Practical exercises on training equipment with SINAMICS DC MASTER

Note:

The replacement of components is communicated in accordance with the operating instructions and the purchasable spare parts. If required, complete repairs of the converter can be performed by Siemens Customer Support.

SIMOREG DC-MASTER Servicing

Description/learning objective

As a maintenance engineer you learn to quickly detect and localize faults in SIMOREG DC-MASTER DC drives, to understanding the principles of operation and function of a drive control in order to select the best measures for fault rectification and to rectify simple faults. You achieve the ability to check the faultless operation of the drive.

Target group

Maintenance personnel

Preconditions

Basic knowledge of electrical engineering

Content

Principle of operation, structure and function of DC motors:

• DC shunt motor
• Thyristor power controller
• Binector configuration
• Software structure, control and regulation

Troubleshooting:

• Faults due to overloading
• Faults in the drive control
• Interpretation of device internal fault messages
• Localize faults with a diagnostics tool (DriveMonitor)
• Measures for motor replacement
• Procedure for the exchange of a processor and printed circuit boards
• Check correct functioning
• Compiling and evaluating fault information
• Preventative measures against future failures: Cause analysis, possible preventative measures