Power cables for SINAMICS S120 Siemens
- For SIMOTICS T-1FW6 motors
- For SIMOTICS L-1FN3 motors
- For SIMOTICS L-1FN6 motors
- For SIMOTICS M-1PH8 motors with terminal box
- For SIMOTICS S-1FK7/-1FT7/M-1PH8 motors with full-thread connector
- For SIMOTICS S-1FK7 motors with SPEED-CONNECT connector
- For SIMOTICS S-1FK7/-1FT7/M-1PH8 motors with SPEED-CONNECT connector
Обзор
Power cable for connecting a SIMOTICS M‑1PH8 motor with terminal box to a SINAMICS S120 Motor Module
Power cable with supplied connector for connecting a SIMOTICS S‑1FT7/‑1FK7/ SIMOTICS M‑1PH8 motor to a SINAMICS S120 Motor Module
The synchronous and asynchronous motors are connected to the Motor Modules or Power Modules by means of MOTION‑CONNECT power cables.
The pre-assembled MOTION‑CONNECT power cables are of high quality and offer safety with problem-free functioning.
Depending on the design, the MOTION‑CONNECT power cables are either pre-assembled at one end or at both ends.
If pre-assembled power cables are to be installed in a cable carrier in such a way that the connector would inhibit assembly, pre-assembled cables without assembled connector can also be supplied. In this case, the contacts of the cables are crimped and the connector enclosure is supplied separately. After installing the cables, the customer assembles the connector enclosure.
The 6FX.002‑5.... power cables are available with crimped contacts and with the connector enclosure supplied separately (not in the case of power cables with exposed core ends or cable lugs).
Power cables with separately supplied motor-end connector enclosure. In this case, the 6th position of the Article No. must be changed from 0 to 4: 6FX.042‑5...‑.... (not in the case of power cables with exposed core ends on the motor end).
Power cables with separately supplied module-end connector enclosure. In this case, the 6th position of the Article No. must be changed from 0 to 1: 6FX.012‑5....‑.... (not in the case of power cables for SINAMICS S120 Power Modules or booksize compact).
Type of delivery of pre-assembled power cables
Pre-assembled power cables can be ordered in length units of 10 cm (3.94 in) up to a maximum length of 299 m (984 ft).
The cables are supplied on reels up to 30 kg or 100 m (66.2 lb or 328 ft). Above 30 kg or 100 m (66.2 lb or 328 ft), cable drums are used instead of reels. This applies to both pre-assembled power cables and for cables sold by the meter.
Type of delivery of power cables sold by the meter
Fixed lengths
Cross-section | Brake cores | MOTION‑CONNECT 500 |
|---|---|---|
1.5 mm2 | with/without | 50 m (164 ft), 100 m (328 ft), |
2.5 mm2 | with/without | 50 m (164 ft), 100 m (328 ft), |
Variable length, available in exact meter lengths
Cross-section | Brake cores | MOTION‑CONNECT 500 | MOTION‑CONNECT 800PLUS |
|---|---|---|---|
4 mm2 | with/without | ≤ 500 m (1641 ft) | ≤ 500 m (1641 ft) |
6 mm2 | with/without | ≤ 500 m (1641 ft) | ≤ 500 m (1641 ft) |
10 mm2 | with/without | ≤ 500 m (1641 ft) | ≤ 500 m (1641 ft) |
16 mm2 | with/without | ≤ 200 m (656 ft) | ≤ 200 m (656 ft) |
25 mm2 | without | ≤ 200 m (656 ft) | – |
with | ≤ 200 m (656 ft) | ≤ 200 m (656 ft) | |
35 mm2 | without | ≤ 200 m (656 ft) | – |
with | ≤ 200 m (656 ft) | ≤ 200 m (656 ft) | |
50 mm2 | without | ≤ 200 m (656 ft) | – |
with | ≤ 200 m (656 ft) | ≤ 200 m (656 ft) | |
70 mm2 | without | ≤ 100 m (328 ft) | – |
95 mm2 | without | ≤ 100 m (328 ft) | – |
120 mm2 | without | ≤ 100 m (328 ft) | – |
Характеристика
Characteristic curves for MOTION‑CONNECT 800PLUS
The blue area beneath the characteristic curve represents the potential range of use for the cables. The characteristic curves represent the tested operating points.
Permissible acceleration for signal and power cables MOTION‑CONNECT 800PLUS up to 16 mm2
Permissible acceleration for power cables MOTION‑CONNECT 800PLUS with 25 mm2, 35 mm2 and 50 mm2
Технические данные
Power cables | MOTION‑CONNECT 500 | MOTION‑CONNECT 800PLUS |
| 6FX500.‑....‑.... | 6FX800.‑.....‑.... |
Approvals, according to | ||
| Yes | Yes |
| UL 758, CSA‑C22.2‑N.210.2‑M90 | UL 758, CSA‑C22.2‑N.210.2‑M90 |
| Yes | Yes |
| Yes | Yes |
Rated voltage V0/V in accordance with EN 50395 | ||
| 600 V/1000 V | 600 V/1000 V |
| 24 V (EN) 1000 V (UL/CSA) | 24 V (EN) 1000 V (UL/CSA) |
Test voltage, rms | ||
| 4 kV | 4 kV |
| 2 kV | 2 kV |
Operating temperature on the surface | ||
| ‑20 … +80 °C (‑4 ... +176 °F) | ‑50 … +80 °C (‑58 ... +176 °F) |
| 0 … 60 °C (32 ... 140 °F) | ‑20 … +60 °C (‑4 ... +140 °F) |
Tensile stress, max. | ||
| 50 N/mm2 (7252 lbf/in2) | 50 N/mm2 (7252 lbf/in2) |
| 20 N/mm2 (2901 lbf/in2) | 20 N/mm2 (2901 lbf/in2) |
Smallest bending radius | ||
| 5 × Dmax | 4 × Dmax |
| See selection and ordering data | See selection and ordering data |
Torsional stress | Absolute 30°/m | Absolute 30°/m |
Bending | 100000 | 10 million |
Traversing velocity | 30 m/min (98.4 ft/min) | Up to 300 m/min (984 ft/min) |
Acceleration | 2 m/s2 (6.56 ft/s2) | Up to 50 m/s2 (164 ft/s2) |
Insulation material, incl. jacket | CFC/silicone-free | CFC/halogen/silicone-free |
Oil resistance | EN 60811‑2‑1 | EN 60811‑2‑1 |
Outer jacket | PVC | PUR, HD22.10 S2 (VDE 0282, Part 10) |
DESINA color orange RAL 2003 | DESINA color orange RAL 2003 | |
Flame-retardant | EN 60332‑1‑1 to 1‑3 | EN 60332‑1‑1 to 1‑3 |
Degree of protection of the pre-assembled power cables and their extensions when closed and connected: IP67.
1) The respective registration number is printed on the cable jacket (only applies to power cables).
2) The File No. is printed on the cable jacket.
Ответ от производителя может занять до 5 дней и более.
