SIPLUS master interface modules for IM 151 CPU Siemens

Область применения

The master interface module adds a DP master interface to the IM 151-7(F-)CPU / IM 151-8(F) PN/DP CPU. A lower-level PROFIBUS DP line can thus be established. This results in the following advantages:

Offloading of the central controller by means of distributed preprocessing
IM 151-7 (F-)CPU / IM 151-8(F) PN/DP CPU is possible as DP master in stand-alone mode
Use of the CPU in hierarchical networks, e.g. with IE/PB Link also on Ethernet (CBA, etc.)

Обзор

PROFIBUS DP master interface module for interface module IM 151-7 (R) CPU / IM 151-8 (F) PN/DP CPU

Integrated 12 Mbit/s PROFIBUS DP master interface in Cu version
Allows parallel operation of two PROFIBUS DP interfaces on one IM 151-7 CPU
Allows operation of one PROFIBUS DP interface with an IM 151-8 (F) PN/DP CPU
Increase in availability of systems and machines
Functionality in accordance with a DP master configured interface of an S7-314 CPU

Programming is performed with STEP 7 from version V5.2 with Service Pack 1.

Note:

SIPLUS extreme products are based on SIMATIC standard products. The contents listed here were taken from the respective standard products. SIPLUS extreme specific information was added.

	SIPLUS master interface module for IM 151 CPU
Article No.	6AG1 138-4HA00-7AB0
BasedOn Article No.	6ES7 138-4HA00-0AB0
Ambient temperature range	-25 °C … +70 °C
Conformal coating	Coating of the printed circuit boards and the electronic components
Technical data	The technical data of the standard product applies except for the ambient conditions.
Ambient conditions
Relative humidity	100%, condensation/frost permitted. No commissioning in bedewed state.
Biologically active substances, compliance with EN 60721-3-3	Class 3B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!
Chemically active substances, compliance with EN 60721-3-3	Class 3C4 incl. salt spray in accordance with EN60068-2-52 (degree of severity 3). The supplied plug covers must remain in place over the unused interfaces during operation!
Mechanically active substances, compliance with EN 60721-3-3	Class 3S4 incl. sand, dust. The supplied plug covers must remain in place over the unused interfaces during operation!
Air pressure (depending on the highest positive temperature range specified)	1 080 ... 795 hPa (-1 000 … +2 000 m) See ambient temperature range 795 ... 658 hPa (+2 000 ... +3 500 m) derating 10 K 658 … 540 hPa (+3 500 … +5 000 m) derating 20 K

For technical documentation on SIPLUS, see:

http://www.siemens.de/siplus-extreme

Дизайн

The master interface module has a 9-pin Sub-D connector (socket) for connecting to PROFIBUS DP.

Installation information:
The master interface module is to be plugged in to the right of the IM 151-7 (F-) CPU / IM 151-8(F) PN/DP CPU.

Функции

The master interface module adds a DP master interface to the IM 151-7(F-)CPU / IM 151-8(F) PN/DP CPU. The functionality and quantity structures are defined by the IM 151-7 (F-)CPU / IM 151-8(F) PN/DP CPU.

The master interface module also enables connection of a programming device to its interface. This makes routing to bus nodes possible on the integral CPU interface possible if it is operated in active mode.

Технические данные

Order number		6AG1138-4HA00-7AB0
		SIPLUS ET200S DP-MASTER INTERFACE
Hardware configuration
Number of modules per CPU		1
Ambient conditions
Ambient temperature during operation
● min.		-40 °C; = Tmin
● max.		70 °C; = Tmax
Extended ambient conditions
● relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width		35 mm
Height		119.5 mm
Depth		75 mm
Weights
Weight, approx.		100 g