ABB – высокотехнологичная компания, лидирующая в разработке систем автоматизации промышленных производств. Её история началась ещё 130 лет назад, и сейчас филиалы ABB работают в 100 странах, а количество служащих превышает 135,000 человек.
Уже более 40 лет специалисты ABB занимаются разработкой инновационных технологий цифрового соединения и управления промышленным оборудованием и системами. За это время на предприятиях заказчиков были установлены и введены в эксплуатацию 70,000 систем управления, объединяющие более 70 миллионов устройств.
Каждый день компания выпускает новые решения безопасности, эффективности и продуктивности для коммунальной и промышленной сферы, транспорта и инфраструктуры по всему миру.
Вся продукция, системы и комплексные решения ABB разрабатываются с заботой об окружающей среде. Вредное воздействие на природу снижается за счёт повышения энергоэффективности и продуктивности оборудования.
Закажите в нашем магазине
Нужна редкая деталь? Закажем оригинал или надёжный аналог из Европы, США или Китая — по договору и с «белой» таможенной очисткой.
Long Description:Device to control of apartment ranges, typically in hotels and small apartments. 12 inputs, 4 outputs and 4 shutter outputs or 8 outputs.
Long Description:KNX power supplies 320 mA generate and monitor the KNX system voltage (SELV). The bus line is decoupled from the power supply by an integrated choke. The voltage output is short-circuit and overload protected. The two-color LED indicates device output sta
Long Description:KNX power supplies 640 mA generate and monitor the KNX system voltage (SELV). The bus line is decoupled from the power supply by an integrated choke. The voltage output is short-circuit and overload protected. The two-color LED indicates device output sta
Long Description:For the control of loads in residential areas, typically in hotel rooms and apartments. The I/O Actuators provide binary inputs for the connection of conventional push-buttons and outputs for switching loads. Inputs and outputs can be internally connected
Long Description:For the control of loads in residential areas, typically in hotel rooms and apartments. The I/O Actuators provide binary inputs for the connection of conventional push-buttons and outputs for switching loads. Inputs and outputs can be internally connected
Long Description:The ABB i-bus® KNX Line Coupler LK/S 4.2 is a modular installation device with a module width of 2 space units. It is used as a line or area coupler or as a repeater. As a line coupler, the LK/S connects a line with a main line, as an area coupler it conn
Catalog Description:DLR/A4.8.1.1, DALI Light Cont, 4f, SM
Long Description:Surface mounting Device for switching and dimming of 16 independent groups of luminaries. Up to 64 DALI participants can be connected to one DALI control line. When combined with the light sensor LF/U 2.1 the device can be used as a 8-fold light controlle
Long Description:Connects the KNX bus with the Ethernet network. The device uses the KNXnet/IP protocol for communication (Routing and Tunneling). It can be used as a fast line and area coupler. The full filter table for main groups 0-31 is supported. KNX devices can be p
Long Description:Connects the KNX bus with the Ethernet network. The device uses the KNXnet/IP protocol for communication (Tunneling). KNX devices can be programmed via the LAN using ETS. For this and further clients 5 Tunneling Server are available. The IP address can be
Catalog Description:MG/E 4.4.1 Zone Module, 4-fold
Long Description:to connect to Security Panel GM/A 8.1 via the Security-Bus. For expansion of the Security-Panel by 4 detector zones. Used for connection to the exterior perimeter detectors such as magnetic reed contacts and passive glass break sensors. The module has 4 z
Long Description:Uses potential free contacts to switch 2 independent electrical loads via the ABB i-bus®. Manual operation and display of the switching state of the contacts. The 6A-AC3 device is especially suited to switch resistive, inductive or capacitive loads.
Long Description:Uses potential free contacts to switch 4 independent electrical loads via the ABB i-bus®. Manual operation and display of the switching state of the contacts. The 6A-AC3 device is especially suited to switch resistive, inductive or capacitive loads.
Long Description:Uses potential free contacts to switch 8 independent electrical loads via the ABB i-bus®. Manual operation and display of the switching state of the contacts. The 6A-AC3 device is especially suited to switch resistive, inductive or capacitive loads.
Long Description:Uses potential free contacts to switch 12 independent electrical loads via the ABB i-bus®. Manual operation and display of the switching state of the contacts. The 6A-AC3 device is especially suited to switch resistive, inductive or capacitive loads.
Catalog Description:WZ/S 1.3.1.2 Weather Unit, MDRC
Long Description:The weather unit WZ/S is used to detect and process weather data from the weather sensor. The weather sensor is providing data for twilight, brightness in 3 directions, rain, temperature, information on day/night, wind speed, date and time. 4 value memory
Catalog Description:MG/A 4.4.1 Zone Module, 4-fold
Long Description:to connect to Security Panel GM/A 8.1 via the Security-Bus. For expansion of the Security-Panel by 4 detector zones. Used for connection to the exterior perimeter detectors such as magnetic reed contacts and passive glass break sensors. The module has 4 z
Long Description:The analogue input is used to detect and process 4 independent input signals. E.g. 0-1 V, 0-5 V, 0-10 V, 0-20 mA, 4-20 mA, 0-1000 Ohm, PT100, PT1000 and floating contacts. Integrated power supply to generate the 24 V DC voltage for external sensors. The d
Long Description:The weather station is used to detect and process 4 independent input signals acc. DIN IEC 60381 (0-1 V, 0-5 V, 0-10 V, 0-20 mA, 4-20 mA, 0-1000 Ohm, PT100, PT1000 and floating contacts). Integrated power supply to generate the 24 V DC voltage for externa
Long Description:Provides extensive logic functions. The logic editor is integrated into the ETS. Up to 3000 logic gates are possible. Simulation for testing. User-defined function blocks can be created and saved. Requires 24 V DC auxiliary voltage or PoE alternatively.